Help:HowToConnectComputersViaUplink - Revision history

Kannkor: /* How to Connect computers via Uplink */

2018-09-13T01:01:31Z

‎How to Connect computers via Uplink

Kannkor: /* How to Connect computers via Uplink */

2015-04-25T01:26:51Z

‎How to Connect computers via Uplink

Kannkor: /* How to Connect computers via Uplink */

2014-09-30T08:21:06Z

‎How to Connect computers via Uplink

Kannkor at 19:47, 9 November 2011

2011-11-09T19:47:22Z

Kannkor: Created page with "== How to Connect computers via Uplink == Please note, this is an Innerspace feature, and unrelated to ISXOgre. However, here are some common issues people have when trying to s..."

2011-11-09T19:41:28Z

Created page with "== How to Connect computers via Uplink == Please note, this is an Innerspace feature, and unrelated to ISXOgre. However, here are some common issues people have when trying to s..."

New page

== How to Connect computers via Uplink ==

Please note, this is an Innerspace feature, and unrelated to ISXOgre. However, here are some common issues people have when trying to set it up for the first time.

* Do not have connections enabled.
** Right click on innerspace, select Configuration.
** Ensure you have a unique name (make sure it's not the same as other computers). Note: Don't assume you know what is in this slot on your other computers, check. Your "COMPUTER NAME" doesn't matter, its' what is in this spot inside of innerspace.
** Ensure you have "Accept incoming connections" selected. If it is not, place a red dot, hit apply, close EQ2, close innerspace, and restart.
** Your window should look something like this.

@@ Line 18: / Line 18: @@
 ** Press "List_IPs".
 ** You should see LOCAL HOST (your own computer), and a listing of any other computer you entered into the UPLINK INFO tab in Ogrebot.
-** Note: You will have to "connect" them any time innerspace is closed and reopened (note EQ2, but innerspace itself).
+** Note: You will have to "connect" them any time innerspace is closed and reopened (not EQ2, but innerspace itself).

@@ Line 17: / Line 17: @@
 ** Wait about 5 seconds.
 ** Press "List_IPs".
-** You should see LOCAL HOST (your own computer), and a listing of any other computer you entered into eq2chars.inc file.
+** You should see LOCAL HOST (your own computer), and a listing of any other computer you entered into the UPLINK INFO tab in Ogrebot.
 ** Note: You will have to "connect" them any time innerspace is closed and reopened (note EQ2, but innerspace itself).

← Older revision		Revision as of 19:47, 9 November 2011
Line 8:		Line 8:
	** Ensure you have "Accept incoming connections" selected. If it is not, place a red dot, hit apply, close EQ2, close innerspace, and restart.		** Ensure you have "Accept incoming connections" selected. If it is not, place a red dot, hit apply, close EQ2, close innerspace, and restart.
	** Your window should look something like this.		** Your window should look something like this.
		+	[[Image:InnerspaceUplinkWindow.PNG]]
		+
		+	* Didn't "connect" them.
		+	** You have to tell innerspace to connect to your other computer. This can be done via an MCP button.
		+	** Load ogre MCP. [Command: ogre mcp]
		+	** Click on the Other tab.
		+	** Far right side, press "Connect".
		+	** Wait about 5 seconds.
		+	** Press "List_IPs".
		+	** You should see LOCAL HOST (your own computer), and a listing of any other computer you entered into eq2chars.inc file.
		+	** Note: You will have to "connect" them any time innerspace is closed and reopened (note EQ2, but innerspace itself).

@@ Line 5: / Line 5: @@
 * Do not have connections enabled.
 ** Right click on innerspace, select Configuration.
-** Ensure you have a unique name (make sure it's not the same as other computers). Note: Don't assume you know what is in this slot on your other computers, check. Your "COMPUTER NAME" doesn't matter, its' what is in this spot inside of innerspace.
+** Ensure you have a unique name, that matches your COMPUTER NAME. These need to be exactly the same as it will connect over your network using this name.
 ** Ensure you have "Accept incoming connections" selected. If it is not, place a red dot, hit apply, close EQ2, close innerspace, and restart.
 ** Your window should look something like this.